Optical Fiber Fabry-Perot Interferometric Sensor Research Articles

Ultracompact Optical Fiber Sensor for Inner Diameter Measurement

ABSTRACT An ultracompact optical fiber Fabry–Perot interferometric sensor is proposed and demonstrated for inner diameter measurement of a capillary tube. The device is a section of single-mode fiber with an angle-polished end face of 45°. When the device is placed inside the capillary tube and in close contact with its inner wall surface, the reflected light from the angle-polished fiber end face is directed sequentially to the fiber core–cladding, cladding–air, and air–capillary interfaces, respectively, and reflected back, and finally returned to the fiber core after being reflected by the angle-polished fiber end face again. As a result, a cascaded Fabry–Perot interferometer system is constructed, which is well suitable for the inner diameter measurement of the capillary tube. Moreover, the wall thickness of the transparent capillary tube can also be conveniently measured by using the same device in slightly different configuration. The relative error of the measurement is small compared with the data provided by the manufacturer. Such a device is ultracompact, robust, flexible, and convenient in operation and is especially attractive for implementing the measurement in a tight or hard-to-reach spatial environment.

Simultaneous and Multiplexed Measurement of Curvature and Strain Based on Optical Fiber Fabry-Perot Interferometric Sensors

Optical fiber sensors that have a compact size and the capability for multi-parameter sensing are desired in various applications. This article reports a miniaturized optical fiber Fabry-Perot interferometric sensor with a length of hundreds of µm that is able to simultaneously measure variations of curvature, temperature, and strain. The sensor is easy to fabricate, requiring only the fusion splicing of a short section of the silica capillary tube between two single-mode fibers (SMFs). The combined mechanism of the Fabry-Perot interference occurred in the two interfaces between the capillary and the SMFs, and the antiresonant guidance induced by the capillary tube makes the device capable of realizing multi-parameter sensing. A simplified coefficient matrix approach is developed to decouple the contributions from different parameters. In addition, the capability of the device for multiplexing is investigated, where four such prototypes with different air cavity lengths are multiplexed in a system in parallel. The spectral behavior of an individual device for measuring curvature and strain is reconstructed and investigated, showing reliable responses and little crosstalk between different devices. The proposed device is easy to fabricate, cost-effective, robust, and could find potential applications in the field of structural health monitoring and medical and human–machine interactive sensing.

Ultracompact optical fiber high‐temperature sensor based on the angled fiber end face

AbstractAn ultracompact optical fiber Fabry–Perot interferometric sensor is proposed and demonstrated for high‐temperature measurement. The device is simply a section of single‐mode fiber with angled end face of 45°, the reflected light from the angled fiber end face is directed sequentially to the fiber core–cladding and cladding–air interfaces, respectively, and reflected back, and finally returned to the fiber core after being reflected by the angled fiber end face again. As a result, a Fabry–Perot interferometer is constructed. Because of the thermal‐expansion and thermal‐optical effect of the fiber material, the optical path difference between the core–cladding and cladding–air surfaces is changed with temperature, hence the device is well suitable for temperature measurement. In particular, the fiber device has good high‐temperature sustainability up to 1100°C, which makes it attractive for high‐temperature measurement in a narrow or hard‐to‐reach spatial environment.

An all-optical off-beam quartz-enhanced photoacoustic spectroscopy employing double-pass acoustic microresonators

An all-optical off-beam quartz-enhanced photoacoustic spectroscopy (QEPAS) sensor employing double-pass acoustic microresonators was proposed and experimentally investigated. An optical fiber Fabry–Perot interferometric sensor with quadrature point self-stabilization was employed for the detection of quartz prong vibration. A commercial quartz tuning fork with a resonant frequency of 30.72 kHz was employed as an acoustic transducer. Water vapor as the catalyst was added for improving the vibrational energy transfer. The minimum detection limit of ∼2.41 ppmv was obtained with a 1 s averaging time, which corresponded to a normalized noise equivalent absorption coefficient of 7.76×10−8 cm−1 W Hz−1/2 at the methane absorption line of 6046.95 cm −1 with an optimized modulation depth of 0.172 cm −1. The detection sensitivity was enhanced by a factor of ∼1.48 in comparison to the off-beam QEPAS employing a single-pass microresonator. An Allan deviation analysis indicated that the ultimate detection limit for the QEPAS-based sensor was ∼0.288 ppmv at the optimum averaging time of ∼125 s.

Optical fiber surface waveguide with Fabry-Perot cavity for sensing.

A parallel structured optical fiber Fabry-Perot interferometer sensor is proposed and demonstrated for refractive index and strain sensing with low temperature cross sensitivity. The device consists of two Fabry-Perot cavities fabricated by a femtosecond laser: one is inscribed in the fiber surface waveguide and used for sensing, and the other one is located in the fiber core for referencing. Part of the light propagating in the fiber core can be directed to the fiber surface waveguide via an X coupler. Because of the evanescent field, the light traveling along the fiber surface waveguide interacts with the surrounding medium and enables external refractive index sensing. The measurement sensitivity of the device is enhanced due to the Vernier effect associated with the parallel structured two Fabry-Perot interferometers. The sensitivities of ∼843.3nm/RIU and ∼101.8pm/µε have been obtained for refractive index and strain, respectively, and the corresponding temperature cross sensitivities are ∼9.6×10-6RIU/∘C and ∼7.956×10-2µε/∘C, respectively. The device is featured with high robustness, compact size, and large sensitivity.

Continuous Hue-Based Self-Calibration of a Smartphone Spectrometer Applied to Optical Fiber Fabry-Perot Sensor Interrogation.

Smartphone-based optical spectrometers allow the development of a new generation of portable and cost-effective optical sensing solutions that can be easily integrated into sensor networks. However, most commonly the spectral calibration relies on the external reference light sources which have known narrow spectral lines. Such calibration must be repeated each time the fiber and diffraction grating holders are removed from the smartphone and reattached. Moreover, the spectrometer wavelength scale can drift during the measurement because of the smartphone temperature fluctuations. The present work reports on a novel spectral self-calibration approach, based on the correspondence between the light wavelength and the hue features of the spectrum measured using a color RGB camera. These features are caused by the nonuniformity of camera RGB filters’ responses and their finite overlap, which is a typical situation for RGB cameras. Thus, the wavelength scale should be externally calibrated only once for each smartphone spectrometer and can further be continuously verified and corrected using the proposed self-calibration approach. An ability of the plug-and play operation and the temperature drift elimination of the smartphone spectrometer was experimentally demonstrated. Conducted experiments involved interrogation of optical fiber Fabry-Perot interferometric sensor and demonstrated a nanometer-level optical path difference resolution.

Optical Fiber Fabry-Perot Interferometer Sensor Fabricated by Femtosecond Laser-Induced Water Breakdown

The Fabry-Perot interferometer sensor in the optical fiber fabricated by femtosecond laser in the water is investigated in this article. The Fabry-Perot interferometer fabricated with different laser pulse energies and cavity lengths are discussed in the air and water. It is concluded that the Fabry-Perot interferometer with 60 mW in the water has more obvious fringe visibility, and the method has high potentials in Fabry-Perot interferometer fabrication.

An optical fiber Fabry-Perot interferometric sensor based on functionalized diaphragm for ultrasound detection and imaging

A miniature optical fiber ultrasonic sensor based on the Fabry-Perot interferometer (FPI) is proposed and experimentally demonstrated. The cavity of the interferometer is based on a section of hollow core fiber coated with a 353ND diaphragm. A well-define interference pattern is achieved, and the spectral sideband filter technique is used to interrogate the sensor. Because the thin reflective diaphragm is extremely sensitive to sound pressure, the signal-to-noise ratio of the sensor response reaches to 31.22 dB with the pulse ultrasonic excitation of 300 kHz. A clear interface information can be distinguished in physical model imaging, and the longitudinal spatial resolution is 5 mm. This proposed sensor has the advantages of being simple to fabricate, ultracompact in size, cost effective, corrosion resistance, and being highly stable.

Optical fiber Fabry-Perot interferometric sensor for magnetic field measurement

A fiber-optic sensor based on the extrinsic Fabry-Perot interferometer (EFPI) is demonstrated to measure dc magnetic fields (100-35000 nT). A Metglas (Fe/sub 77.5/B/sub 15/Si/sub 7.5/) wire-based magnetostrictive transducer is used as the reflector in two quadrature-phase-shifted EFPI sensor elements which are used to overcome phase ambiguity in the interferometric sensor. The simple sensor geometry gives both relatively low-vibration sensitivity and better than 99% compensation for thermally induced fluctuations.